|
PM CONCENTRATE is a fiber
reinforced, gray cement based, factory blended mixture
designed as a cement plaster base coat requiring only
the addition of sand and water on the job site.
PM CONCENTRATE NF is
a gray cement based, factory blended mixture designed
as a cement plaster base coat requiring the addition
of sand, fibers (for crack resistance) and water on
the job site.
PM CONCENTRATE WS is
a fiber reinforced, gray cement based, factory blended
mixture designed as a cement plaster base coat requiring
only the addition of water on the job site. The sand
is in the mixture.
 |
Fire resistance |
|
Superior bonding |
|
Excellent workability |
|
Rot & fungus resistant |
|
A hard, durable surface |
|
Greater crack resistance |
PM CONCENTRATE is made
up of gray cement, hydrated lime, fiber strands and
other additives that enhance the performance of the
product.
PM CONCENTRATE NF is
made up of gray cement, hydrated lime and other additives
that enhance the performance of the product.
PM CONCENTRATE WS is
made up of gray cement, hydrated lime, fiber strands,
silica sand and other additives that enhance the performance
of the product.
All components in the manufacturing of PM
CONCENTRATE, PM CONCENTRATE
NF and PM CONCENTRATE
WS meet the standards set forth in ASTM
C-926-98a.USES
PM CONCENTRATE and PM
CONCENTRATE WS are the products of choice when
a superior cement plaster coating is desired. They have
exceptional workability and the fiber reinforcing strands
greatly reduce the possibility of cracking.
PM CONCENTRATE NF is
the product of choice when the applicator chooses to
be responsible for the addition of most ingredients
on the job site that constitute a viable cement plaster
base coat.
Surfaces to be plastered should be inspected by the
contractor and any unsatisfactory conditions should
be reported and corrected prior to the application of
PM CONCENTRATE, PM
CONCENTRATE NF or PM CONCENTRATE
WS. All flashings, hangers, fasteners, trim or
other fixed supports shown on the plans, should be in
place prior to application of base coat. Dust, dirt
or loose particles should be removed from concrete or
masonry surfaces prior to application. Masonry surfaces
should be uniformly moistened before the application
of either product. These products should not be applied
to surfaces that contain frost. Provisions should be
made to keep the products at a temperature of 45°F
(7°C) to 100°F
(38°C) during application
and for a period of at least 48 hours after application.
Adicote bonding agent must be applied to all poured
concrete or smooth concrete surfaces. Control and/or
expansion joints should be installed in accordance with
ASTM C-1063-99 to alleviate cracking from building component
movement, shrinkage or stress. Location of control joints
must be determined by the designer.
Note: The effectiveness
of these products depend upon proper application, curing
and the conditions and preparation of the surface to
which they are applied. PM CONCENTRATE,
PM CONCENTRATE NF and
PM CONCENTRATE WS should
be applied to wire lath by sections in 1 or 2 coats
to a minimum of 3/8" thickness using sufficient
pressure to form a good bond. If a finish coat is desired
use a factory prepared, pigmented mix such as any of
the colored stucco products manufactured by PREMIX-MARBLETITE
MFG. CO. or a synthetic finish coat, such as
that manufactured by ACROCRETE,
INC. The finish coat must be applied according
to the application specifications for the finish selected.
To avoid abrupt changes in the uniform appearance of
the succeeding coats, each coat must be applied to an
entire wall or ceiling panel without interruptions.
The joining of wet cement plaster should be made at
naturally occurring interruptions such as corners, control
joints or structure levels; otherwise, the stopping
and starting joints may be visible through the finish
coat. Just prior to the application of the finish coat,
the brown coat should be uniformly dampened to attain
uniform suction.
It is essential that the applied cement plaster be
kept moist until setting and hardening has occurred.
Proper hydration requires sufficient water, favorable
temperatures and time. Moist curing (fogging)
is necessary because the large exposed surfaces permit
rapid evaporation of the water used in the mixing process.
Proper curing will develop maximum strength and density.
Newly installed walls should be protected from hot/dry
winds or excessive ventilation. The temperature of the
walls must be maintained above 45°F (7°C)
and below 100°F (38°C)
for no less than 48 hours after application. After application,
the cement plaster should be considered as a thin section
of Portland cement concrete.
If the finish coat is an integrally colored stucco
such as the ones manufactured by PREMIX-MARBLETITE
MFG. CO. or a synthetic finish coat, such as
that manufactured by ACROCRETE,
INC. occasional pressure washing between 500
and 1,000 p.s.i. should produce satisfactory results.
|
These products are not considered
waterproofing products. |
|
These products are cement based and
as such, cracking is not considered a product defect
and is not warrantable. |
|
Too much water or over wetting the
mix will result in separation, texture
variation, low strength and cracking. |
The effectiveness of these products depends upon their
proper application and the condition and preparation
of the surface to which they are applied.
Limited Warranty: The product shall be in its unopened
package and of the kind specified within. THERE IS NO
OTHER WARRANTY OR REPRESENTATION OF ANY KIND, EXPRESS
OR IMPLIED (INCLUDING NO WARRANTY
OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE).
No warranty shall be implied by law. This limited warranty
continues only until such time as the buyer opens the
package and examines its contents. If the buyer, after
opening the package and examining its contents, determines
that the product is not of the kind specified herein,
the buyer should write to PREMIX-MARBLETITE MANUFACTURING
COMPANY, 1259 NW 21st Street, Pompano Beach, Florida
33069, explaining the defect and enclosing a sample
of the product. PREMIX-MARBLETITE, upon receipt of the
sample from the buyer, will replace the portion of the
product that is determined to be defective. This shall
be the buyer's sole remedy for breach of warranty and
such remedy shall be in lieu of any claim for damages,
including consequential damages. Some states do not
allow limitations on how long an implied warranty lasts,
or exclusions or limitations of incidental or consequential
damages, so the above limitations or exclusions may
not apply to you. This warranty gives you specific legal
rights, and you may also have other rights, which vary
from state to state.
(Available upon request)
1259 N.W. 21st STREET
POMPANO BEACH, FL 33069
(954) 917-7665
(800) 432-5097
FAX (954) 917-2775
3110 MOON STATION ROAD
SUITE 100
KENNESAW, GA 30144
(770) 422-4383
FAX (770) 422-3360 o (800) 535-7804
MAUFACTURING FACILITY
325 OLD SANFORD OVIEDO ROAD
WINTER SPRINGS, FL 32708
(407) 327-0830
(800) 432-5539
FAX (407) 327-8942
|
