|
PM CONCENTRATE CCP is
a fiber reinforced, factory blended, colored cement
mixture designed as a highly water resistant cement
plaster base and finish coat.
PM CONCENTRATE CCP requires only the addition
of water on the job site.
 |
Greater crack resistance |
|
Excellent workability |
|
A hard, durable surface |
|
Proven weather barrier |
|
Improved stain resistance |
|
Available in standard and custom
colors |
PM CONCENTRATE CCP is
made up of cement, lime, fiber strands, colored oxides,
aggregate and other additives that enhance the performance
of the product.
All components in the manufacturing of PM
CONCENTRATE CCP meet the standards set forth
in ASTM
C-926-98a.
PM CONCENTRATE CCP is
the product of choice when a superior, water resistant,
cement plaster coating is desired. It has exceptional
workability and the fiber reinforcing strands greatly
reduce the possibility of cracking. PM
CONCENTRATE CCP is an exceptional base/finish
coat for new construction and renovation work.
Surfaces to be coated should be inspected by the contractor
and any unsatisfactory conditions should be reported
and corrected prior to the application of PM
CONCENTRATE CCP. All flashings, hangers, Fasteners,
trim or other fixed supports shown on the plans, should
be in place prior to application. Dust, dirt or loose
particles should be removed from concrete or masonry
surfaces prior to application. Masonry
surfaces should be uniformly moistened before the application.
PM CONCENTRATE CCP should
not be applied to surfaces that contain frost. Provisions
should be made to keep PM CONCENTRATE
CCP at a temperature of 45°F (7°C)
to 100°F (38°C)
during application and for a period of at least 48 hours
after application.
Adicote bonding agent must be applied to all poured
concrete or smooth concrete surfaces. Control and/or
expansion joints should be installed in accordance with
ASTM C-1063-99 to alleviate cracking from building component
movement, shrinkage or stress. Location of control joints
must be determined by the designer.
Measuring equal amounts of water and mixing for equal
amounts of time from batch to batch will ensure product
consistency from batch to batch. Boxing different batch
#'s will ensure final color uniformity. PM
CONCENTRATE CCP will require approximately
1 - 1½ gallons of potable water per bag. Start
the mixing process by adding 2/3 of the total required
water to the mixer. Add the appropriate amount of PM
CONCENTRATE CCP and then add the remaining 1/3
of the required water. Mix for approximately 5 - 8 minutes
to bring the material to a workable consistency. Allow
the mix to set for 5 minutes, then remix and add additional
water if necessary to achieve the desired workable consistency.
Do not retemper the mix after this.
Note: The effectiveness of PM
CONCENTRATE CCP depends upon proper application,
curing and the conditions and preparation of the surface
to which it is applied. Review Application Guidelines
for substrate conditions and preparation. PM
CONCENTRATE CCP should be applied to wire lath
by sections to a minimum of ½" thickness
using sufficient pressure to form a good bond. The finish
texture must be applied while the base coat is still
wet and according to the application specifications
for the texture selected.
NOTE: To avoid abrupt changes
in the uniform appearance of the succeeding coats,
PM CONCENTRATE CCP must
be applied to an entire wall or ceiling panel without
interruptions. The joining of wet product should be
made at naturally occurring interruptions such as corners,
control joints, or structure levels; otherwise, the
stopping and starting joints may be visible through
the finish texture.
Reference Premix-Marbletite application instructions
entitled:
"Base Coat Stucco Products" for specific applications
to selected substrates.
Proper hydration requires sufficient water, favorable
temperatures and time. Newly installed walls should
be protected from hot/dry winds or excessive ventilation.
The temperature of the walls must be maintained above
45°F (7°C) and
below 100°F (38°C)
for no less than 48 hours after application. After application,
the cement plaster should be considered as a thin section
of Portland cement concrete.
PM CONCENTRATE CCP is
a cementitious product, and as such cracking or color
variation is not to be considered a product defect.
NEITHER CRACKING NOR COLOR VARIATION ARE WARRANTABLE.
(Available upon request)
Occasional pressure washing between 500 and 1,000 p.s.i.
should produce satisfactory results.
The effectiveness of this product depends upon its
proper application and the condition and preparation
of the surface to which it is applied.
Limited Warranty: The product shall be in its unopened
package and of the kind specified within. THERE IS NO
OTHER WARRANTY OR REPRESENTATION OF ANY KIND, EXPRESS
OR IMPLIED (INCLUDING NO WARRANTY
OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE).
No warranty shall be implied by law. This limited warranty
continues only until such time as the buyer opens the
package and examines its contents. If the buyer, after
opening the package and examining its contents, determines
that the product is not of the kind specified herein,
the buyer should write to PREMIX-MARBLETITE MANUFACTURING
COMPANY, 1259 NW 21st Street, Pompano Beach, Florida
33069, explaining the defect and enclosing a sample
of the product. PREMIX-MARBLETITE, upon receipt of the
sample from the buyer, will replace the portion of the
product that is determined to be defective. This shall
be the buyer's sole remedy for breach of warranty and
such remedy shall be in lieu of any claim for damages,
including consequential damages. Some states do not
allow limitations on how long an implied warranty lasts,
or exclusions or limitations of incidental or consequential
damages, so the above limitations or exclusions may
not apply to you. This warranty gives you specific legal
rights, and you may also have other rights, which vary
from state to state.
The information contained in this bulletin conforms
to the standard detail recommendations and specifications
for the installation of the products manufactured by
PREMIX-MARBLETITE and is presented in good faith.
PREMIX-MARBLETITE assumes no liability, expressed or
implied, as to the architecture, engineering or workmanship
of any project.
PREMIX-MARBLETITE MFG. CO.
1259 NW 21ST STREET
POMPANO BEACH, FL 33069
(954) 917-7665
FAX (954) 917-2775 · (800) 432-5097
PREMIX-MARBLETITE MFG. CO.
325 OLD SANFORD OVIEDO ROAD
WINTER SPRINGS, FL 32708
(407) 327-0830
FAX (407) 327-8942 · (800) 432-5539
AN III IMPERIAL INDUSTRIES COMPANY
|
