|
DECKOTE is an interior
or exterior 100% acrylic coating that is designed to
provide a surface coating for pool decks, patios, walkways
and driveways. DECKOTE
is available in either sanded or smooth formulas. The
sanded version is specifically prepared for pool decks
to provide for a slip-resistant surface. DECKOTE
is offered in a wide range of standard and custom colors.
DECKOTE is a durable
surface coating that can be used to protect and decorate
cementitious patios, swimming pool decks, walkways and
driveways. It is user friendly as it comes complete
in 5 gallon pails. It can be roller, spray or brush
applied. DECKOTE is recommended
for both new and renovation applications where a new
surface color coating is desired.
 |
Ease of application |
|
Water clean up |
|
VOC compliant |
|
Mildew resistant |
|
Vapor permeable |
|
Excellent weather resistance |
|
Standard & custom colors available |
DECKOTE is packaged in
5 gallon pails and must be applied at a rate not to
exceed 800 - 1000 square feet per pail. Coverage will
vary due to irregular or very porous surfaces.
Patch, level or resurface as required to provide a
smooth substrate. Surface must be clean, cool, dry,
free of dirt, grease, scaling paint, release agents,
curing agents, special surface hardeners, efflorescence
or other foreign matter. Some surfaces may require power
washing prior to coating. If detergents, cleaners or
caustics are used, the surface must be thoroughly rinsed
prior to application. Surface cracks greater than 1/16"
must be patched with crack filler compound prior to
application. Refer to ASTM D-4258 and ASTM D-4261 for
complete details on preparing cementitious substrates
for coatings.
Mix with a clean, rust-free, slow speed electric drill
and paddle. Avoid excessive mixing, as this will entrap
air into the coating.
DECKOTE is applied by
brush, roller or proper spray equipment in a two-coat
application. Allow the first coat to dry to the touch
before application of the second coat. Maintain a wet
edge to eliminate cold joints and to assure uniformity
of color. Keep tools and equipment clean. Protect from
rain and freezing temperatures until completely cured.
DECKOTE should be ready
to receive light traffic within 8 hours.
Drying Time - The drying
time is dependent upon ambient temperature, relative
humidity and wind conditions. Under average drying conditions
(70EF, 55% R.H.), DECKOTE
is dry to the touch in ½ hour and dry enough
to re-coat in 2 hours.
Clean all tools and equipment with water while still
wet. Cured material can be removed mechanically or chemically.
Protect from freezing and extreme heat. Store at 40EF
or above in tightly sealed containers out of direct
sunlight.
Apply only when surface and ambient temperatures are
40EF - 100EF and relative humidity is below 85% throughout
the application and drying time. Allow fresh concrete
and masonry substrates to cure for at least 28 days
prior to coating.
|
Do not apply when there is a threat
of rain or when humidity is 85% or higher. |
|
Do not apply to any surface that is
frozen or that has not completely thawed, dried
and has reached a surface temperature of 40EF. |
|
Do not use on below grade or immersed
surfaces. Interior surfaces where hydrostatic pressure
is present (ground moisture/water
pressure) may cause coating to delaminate.
|
DECKOTE is not designed
to be used in areas where there is standing water. Caution
should be taken to assure that the substrate does not
allow for standing water as bond loss could occur.
For safety DECKOTE SANDED
should be used whenever the deck areas are going to
be exposed to water as the DECKOTE
SMOOTH could become slippery when wet.
(Available upon request)
The effectiveness of this product depends upon its
proper application and the condition and preparation
of the surface to which it is applied.
Limited Warranty: The product shall be in its unopened
package and of the kind specified within. THERE IS NO
OTHER WARRANTY OR REPRESENTATION OF ANY KIND, EXPRESS
OR IMPLIED (INCLUDING NO WARRANTY
OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE).
No warranty shall be implied by law. This limited warranty
continues only until such time as the buyer opens the
package and examines its contents. If the buyer, after
opening the package and examining its contents, determines
that the product is not of the kind specified herein,
the buyer should write to PREMIX-MARBLETITE MANUFACTURING
COMPANY, 1259 NW 21st Street, Pompano Beach, Florida
33069, explaining the defect and enclosing a sample
of the product.
PREMIX-MARBLETITE, upon receipt of the sample from the
buyer, will replace the portion of the product that
is determined to be defective. This shall be the buyer's
sole remedy for breach of warranty and such remedy shall
be in lieu of any claim for damages, including consequential
damages. Some states do not allow limitations on how
long an implied warranty lasts, or exclusions or limitations
of incidental or consequential damages, so the above
limitations or exclusions may not apply to you. This
warranty gives you specific legal rights, and you may
also have other rights, which vary from state to state.
The information contained in this bulletin conforms to
the standard detail recommendations and specifications
for the installation of the products manufactured by
PREMIX-MARBLETITE and is presented in good faith. PREMIX-MARBLETITE
assumes no liability, expressed or implied, as to the
architecture, engineering or workmanship of any project.
1259 N.W. 21st STREET
POMPANO BEACH, FL 33069
(954) 917-7665
(800) 432-5097
FAX (954) 917-2775
PREMIX-MARBLETITE MFG CO.
325 OLD SANFORD OVIEDO ROAD
WINTER SPRINGS, FL 32708
(407) 327-0830
FAX (407) 327-8942 o (800) 432-5539
AN III IMPERIAL INDUSTRIES COMPANY
|
Deckote
