|
DECKRETE is a one component,
polymer modified cementitious textured base coat designed
for use on interior or exterior cementitious substrates.
DECKRETE is formulated
to provide excellent bonding to new and existing cementitious
substrates.
DECKRETE is spray applied
to properly prepared cementitious substrates and then
coated with Deckote to create durable, aesthetically
pleasing high design decks, patios, walkways and driveways.
 |
Vapor permeable |
|
Easy application |
|
Water clean up |
|
Excellent adhesion |
|
Cooler deck surfaces |
|
A hard, durable finish |
|
An anti-slip textured surface |
DECKRETE is packaged
in 50 lb. bags and must be applied at a rate not to
exceed 200-250 square feet per bag. Coverage will vary
depending on the desired texture and the porosity of
the substrate.
Patch, level or resurface as required to provide a
smooth substrate. Surface must be clean, cool, dry,
free of dirt, grease, scaling paint, release agents,
curing agents, special surface hardeners, efflorescence
or other foreign matter. Some surfaces may require power
washing prior to coating. If detergents, cleaners or
caustics are used, the surface must be thoroughly rinsed
prior to application. Surface cracks greater than 1/16"
must be patched with crack filler compound prior to
application. Refer to ASTM
D-4258 and ASTM D-4261 for complete details on preparing
cementitious substrates for coatings.
Measuring equal amounts of water and mixing for equal
amounts of time from batch to batch will ensure product
consistency from batch to batch. DECKRETE
will require approximately 1-1 ½ gallons of potable
water per bag. Start the mixing process by adding? of
the total required water to the mixer. Add the appropriate
amount of DECKRETE and
then add the remaining? of the required water. Mix for
approximately 5 minutes to bring the material to a workable
consistency. Allow the mix to set for 5 minutes, then
remix and add additional water if necessary to achieve
the desired workable consistency. Do not retemper the
mix after this.
A) Remove all rust, mildew,
mold, algae, fungus, dirt, oil, grease or other foreign
materials that could serve as a bond breaker.
B) Inspect the existing
substrate to make sure that all cracks are filled; all
loose material has been removed and that the substrate
is level.
C) To achieve a "splatter"
texture, fill a hopper gun; adjust the nozzle to the
desired pattern and spray on the DECKRETE.
It is not necessary to cover the entire area; approximately
75% coverage is typical.
D) DECKRETE should be
"knocked down" immediately after it has been
applied. Once the DECKRETE is dry, lightly scrape the
surface to remove any loose material.
E) Coat the DECKRETE
with Deckote Smooth or Sanded in the color of your choice.
Deckote is designed to be either roller or spray applied.
One coat is usually sufficient for full coverage, however
a second coat can be applied if desired. Refer to the
product data sheet for a full description of the Deckote
features and benefits.
Curing Time: Curing of
the DECKRETE is dependent
on the air temperature and relative humidity. Under
average curing conditions (70EF,
55% R.H.) DECKRETE
should be set within 8 hours. Heavy traffic or high
abuse areas may require 48 hours. As with all cementitious
products, 28 days is required for complete cure.
Clean all tools and equipment with water while still
wet. Cured material can be removed mechanically or chemically.
DECKRETE must be protected
from moisture. Store off the ground in a cool, dry location
out of direct sunlight.
Apply only when surface and ambient temperatures are
40EF - 100EF and relative humidity is below 85% throughout
the application and drying time.
|
Do not apply when there is a threat
of rain or when humidity is 85% or higher. |
|
Do not apply to any surface that is
frozen or that has not completely
thawed, dried and has reached a surface temperature
of 40EF. |
|
Do not use on below grade or immersed
surfaces. Interior surfaces where hydrostatic pressure
is present (ground moisture/water
pressure) may cause coating to delaminate. |
(Available upon request)
Occasional pressure washing between 500 and 1000 psi
should produce satisfactory results.
The effectiveness of this product depends upon its
proper application and the condition and preparation
of the surface to which it is applied.
Limited Warranty: The product shall be in its unopened package
and of the kind specified within. THERE IS NO OTHER WARRANTY
OR REPRESENTATION OF ANY KIND, EXPRESS OR IMPLIED (INCLUDING
NO WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR
PURPOSE). No warranty shall be implied by law.
This limited warranty continues only until such time as
the buyer opens the package and examines its contents.
If the buyer, after opening the package and examining
its contents, determines that the product is not of the
kind specified herein, the buyer should write to PREMIX-MARBLETITE
MANUFACTURING COMPANY, 1259 NW 21st Street, Pompano Beach,
Florida 33069, explaining the defect and enclosing a sample
of the product. PREMIX-MARBLETITE, upon receipt of the
sample from the buyer, will replace the portion of the
product that is determined to be defective. This shall
be the buyer's sole remedy for breach of warranty and
such remedy shall be in lieu of any claim for damages,
including consequential damages. Some states do not allow
limitations on how long an implied warranty lasts, or
exclusions or limitations of incidental or consequential
damages, so the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights,
and you may also have other rights, which vary from state
to state.
The information contained in this bulletin conforms
to the standard detail recommendations and specifications
for the installation of the products manufactured by
PREMIX-MARBLETITE and is presented in good faith.
PREMIX-MARBLETITE assumes no liability, expressed or
implied, as to the architecture, engineering or workmanship
of any project.
1259 N.W. 21st STREET
POMPANO BEACH, FL 33069
(954) 917-7665
(800) 432-5097
FAX (954) 917-2775
PREMIX-MARBLETITE MFG. CO.
325 OLD SANFORD OVIEDO ROAD
WINTER SPRINGS, FL 32708
(407) 327-0830
(800) 432-5539
FAX (407) 327-8942
AN III IMPERIAL INDUSTRIES COMPANY
|
Deckcrete
