|
WONCOTE is a gypsum based veneer plaster coating designed
to give either a smooth or sanded finish over veneer
gypsum base boards, blue board, masonry block or concrete
surfaces.
WONCOTE is available in both a smooth and sanded texture
finish. WONCOTE SMOOTH is designed for uniform smooth
troweled finishes to provide an even, level, final finish.
WONCOTE SANDED is designed to either float or provide
rough final finishes. Both products are recommended
for interior applications only and may be used in both
ceiling and wall applications.
 |
Economical - low cost |
|
Superior workability |
|
A hard, durable finish |
|
Accelerated scheduling |
|
A variety of texture options |
|
Excellent scuff, scrubbing and crack
resistance |
WONCOTE SMOOTH is packaged
in 50 lb. bags and WONCOTE SANDED
is packaged in 70 lb. bags. Both products must be applied
at a rate not to exceed 115-135 square feet per bag.
Coverage will vary depending on the desired texture
and the porosity of the substrate.
Patch, level or resurface as required to provide a
smooth substrate. Surface must be clean, cool, dry and
free of dirt, dust, grease, efflorescence or other foreign
matter that may prevent proper bonding. Veneer board
must not be over exposed to sunlight or moisture.
Measuring equal amounts of water and mixing for equal
amounts of time from batch to batch will ensure
product consistency from batch to batch. WONCOTE
will require approximately 2 ½ - 3 gallons of potable
water per bag. Start the mixing process by adding ? of
the total required water to the mixer. Add the appropriate
amount of WONCOTE and then
add the remaining ? of the required water. Mix for approximately
2 - 5 minutes to bring the material to a workable consistency.
Equipment used for mixing must be clean. A common practice
is to use a heavy duty drill capable of producing a minimum
of 650 r.p.m's. under load. Over mixing rapidly shortens
open time. Do not retemper the mix after this.
WONCOTE can be applied
over the following substrates:
Gypsum Veneer Board: Faded discolored, old or other
questionable boards may be coated with Adicote bonding
agent. All joints, corners, angles and squared edges
must be reinforced with joint tape. Embed tape, beads
and trims with a tight, thin coat of WONCOTE
and allow to set. After tape, beads and trims have set,
scratch a thin coat of WONCOTE
over the entire area, immediately doubling back to full
thickness of not less than 1/16" and not more than
1/8". It is best to scratch and double back with
the same mix; avoid inter-mixing batches. During final
troweling, use water sparingly after the surface has
become firm. Do not over trowel.
Porous Cement Block: Apply only to block surfaces that
develop proper suction or are scored to provide adequate
mechanical bond. Apply WONCOTE
in two coats. Trowel on WONCOTE
SANDED as the first coat to sufficiently straighten
wall, but do not trowel smooth. After the first coat
sets, but before it dries, trowel on the second coat
(of either WONCOTE SMOOTH
or WONCOTE SANDED depending
on desired finish). Total thickness should not exceed
1/8".
Monolithic Concrete. To ensure an adequate bond, ADICOTE
must be applied to the entire surface. Apply WONCOTE
in two coats. Trowel on
WONCOTE SANDED as the first
coat to sufficiently straighten wall, but do not trowel
smooth. After the first coat sets, trowel on the second
coat (of either WONCOTE SMOOTH
or WONCOTE SANDED, depending
upon desired finish). Total thickness should not exceed
1/8".
When necessary, in order to enliven the surface, use
a small amount of water and trowel in with additional
material to overcome any blemishes or imperfections.
For sand float finish omit final troweling and instead,
after surface becomes firm, float to desired texture
using sponge or other float system.
After curing WONCOTE
must be coated with a high quality alkaline resistant
paint to protect it from moisture.
This product may cause skin irritation. Any skin contact
should be washed immediately with fresh water. When
mixing this product, wear a respirator which is U.S.
Bureau of Mines approved for toxic nuisance and
pneumoconiosis dusts.
Clean all tools and equipment with water while still
wet. Cured material can be removed mechanically or chemically.
WONCOTE must be protected
from moisture. Store off the ground in a cool, dry location
out of direct sunlight.
Apply only when surface and ambient temperatures are
40EF - 100EF and relative humidity is below 85% throughout
the application and drying time. Do not apply when there
is a threat of rain or when humidity is 85% or higher.
Do not apply to any surface that is frozen or that has
not completely thawed, dried and has reached a surface
temperature of 40EF.
(Available upon request)
Walls may be quickly and easily repaired with various
patching plasters or similar materials.
The effectiveness of this product depends upon its
proper application and the condition and preparation
of the surface to which it is applied.
Limited Warranty: The product shall be in its unopened
package and of the kind specified within. THERE IS NO
OTHER WARRANTY OR REPRESENTATION OF ANY KIND, EXPRESS
OR IMPLIED (INCLUDING NO WARRANTY OF MERCHANTABILITY
OR OF FITNESS FOR A PARTICULAR PURPOSE). No warranty
shall be implied by law. This limited warranty continues
only until such time as the buyer opens the package
and examines its contents. If the buyer, after opening
the package and examining its contents, determines that
the product is not of the kind specified herein, the
buyer should write to PREMIX-MARBLETITE MANUFACTURING
COMPANY, 1259 NW 21st Street, Pompano Beach, Florida
33069, explaining the defect and enclosing a sample
of the product. PREMIX-MARBLETITE, upon receipt of the
sample from the buyer, will replace the portion of the
product that is determined to be defective. This shall
be the buyer's sole remedy for breach of warranty and
such remedy shall be in lieu of any claim for damages,
including consequential damages. Some states do not
allow limitations on how long an implied warranty lasts,
or exclusions or limitations of incidental or consequential
damages, so the above limitations or exclusions may
not apply to you. This warranty gives you specific legal
rights, and you may also have other rights, which vary
from state to state.
The information contained in this bulletin conforms
to the standard detail recommendations and specifications
for the installation of the products manufactured by
PREMIX-MARBLETITE and is presented in good faith.
PREMIX-MARBLETITE assumes no
liability, expressed or implied, as to the architecture,
engineering or workmanship of any project.
1259 N.W. 21st STREET
POMPANO BEACH, FL 33069
(954) 917-7665
(800) 432-5097
FAX (954) 917-2775
PREMIX-MARBLETITE MFG. CO.
325 OLD SANFORD OVIEDO ROAD
WINTER SPRINGS, FL 32708
(407) 327-0830
(800) 432-5539
FAX (407) 327-8942
AN III IMPERIAL INDUSTRIES COMPANY
|
Woncote
